Brand new INT-TSH2 and INT-TSG2
touchscreen keypads

Powerful processor, completely new interface,
swipe gestures support.
Meet the new level
of safety and building automation control.

Alarm control panels
ABAX 2 Two way wireless system
System units
Zones/outputs expansion modules
Motion detectors
Detectors for perimeter protection
Other detectors
Control
Signalling devices
Accessories
MICRA wireless system
Detectors
Sirens
Communication and messaging
Radio remote controllers
Enclosures
Power
Accessories
Software

select products
select products
ACCO NET
ACCO

select products
select products
Software
Hardware solutions
Telephone receivers
Ethernet receivers
Visualization
Sets

select products
select products
ACSP System
CSP System

select products
select products
KNX system
INTEGRA Automation

 

AOCD-260

Outdoor wireless dual curtain detector

The AOCD-260 curtain detector supervises a narrow strip, only 0.6 m wide and 10 m long. The device, which detects movement when the boundary of the protected area is crossed, can be a component of perimeter protection. It works as part of the ABAX 2/ABAX two-way wireless system. The product complies with the EN 50131 Grade 2 requirements (for indoor use).

The detector has two detection paths i.e. infrared and microwave, which can be adjusted independently. The detection is based on digital signal processing supported by dynamic temperature compensation, which ensures proper functioning of the detector within the temperature range from -40°C to +55°C. AOCD-260 supervises the motion detection system and indicates any faults in its operation. The detector is characterized by high immunity to false alarms.

Configuration of the device and updating of its firmware are carried out remotely. Radio communication within the ABAX 2 system is AES encrypted.

AOCD-260 has a three-color LED which indicates, for example, violations in test mode.

The detector is powered by a CR123A 3 V battery. When the level of its charge is lower than the set value, the detector will report low battery. The "ECO" option (available in ABAX 2 only) extends the device operation time even fourfold without battery replacement.

The device has a polycarbonate enclosure (with IP54 protection rating). The detector has tamper protection against opening and removal from the mount. It can be mounted directly on the wall (Grade 2) or, alternatively, using the angle-type bracket.

To increase the detector's distance from the wall, at a distance of even by over a dozen centimeters, it is worth using the BRACKET E modular set. Especially if there is a gutter or lamp in the vicinity of the device, which can limit the full range of the device detection field. A special insert for AGATE / AOCD-260 detectors allows their installation also using BRACKET A and BRACKET B brackets (recommended for indoor installation).

All listed brackets are adapted for wall and ceiling mounting. In addition, BRACKET E and BRACKET B have an enclosed design that makes it easier to hide the cable, thereby improving the overall aesthetics of the installation.

For additional protection of the device against atmospheric precipitation and fouling, you can install the HOOD A protective cover on the detector enclosure.

  • compliance with the EN 50131 Grade 2 requirements (for indoor use)
  • two detection paths: PIR and microwave
  • detection area: 10 m x 0.6 m, angle 6°
  • high immunity to false alarms
  • advanced digital signal processing
  • dynamic compensation of temperature changes
  • compatible with:
  • range of radio communication in the open area:
    • in ABAX 2: up to 2000 m (with ACU-220) / up to 1600 m (with ACU-280)
    • in ABAX: up to 500 m
  • remote configuration and updating of the firmware
  • independently adjustable sensitivity of PIR and MW paths
  • built-in temperature sensor (temperature measurement in the range from -40°C to +55°C)
  • LED indicator of violations in test mode
  • splash-proof, weather-resistant polycarbonate enclosure with IP54 protection rating
  • low energy consumption and battery status check
  • "ECO" option for extending battery life (in ABAX 2 only)
  • power supply: CR123A 3 V battery
  • tamper protection against opening of the enclosure / removal from the mount
  • can be mounted directly on the wall or, optionally, using the:
    • angle-type bracket
    • adjustable holder BRACKET A
      • tilt angle adjustment within approx. 30°
      • swivel angle adjustment within approx. 90°
      • optional wall- or ceiling mounting of detector
    • adjustable holder BRACKET B
      • inner cable duct
      • fully enclosed design for better appearance of installation
      • tilt angle adjustment within approx. 30°
      • swivel angle adjustment within approx. 90°
      • optional wall- or ceiling mounting of detector
    • BRACKET E set
      • BRACKET E-1 (GY) – body for attaching the BRACKET E-2A inserts
      • BRACKET E-2A (GY) – insert for the mounting AOCD-260 curtain detectors
      • BRACKET E-3 (GY) – 30 mm distance piece enabling the detector to be distanced from the wall or ceiling
      • BRACKET E-4 (GY) – 20 mm mounting base
      • BRACKET E-6 – tamper sensor with NO/NC switch and 500 mm long cables
  • option to mount HOOD A protective cover on the detector's enclosure
AOCD-260
The actual appearance of the products may differ from the presented images. Product descriptions are provided in the web service for information purposes only.
quick installer guide
updated: 2024-06-04
405 KB
general information manual
updated: 2023-03-27
889 KB

 © 1990-2021 SATEL sp. z o.o.
legal | privacy policy | Feedback | about site

The Satel.pl website uses cookies to enable Users' to take advantage of Satel.pl features as well as for statistical purposes. Unless you block cookies, you grant your consent for their use and storage in device memory. You must remember that you are able to manage cookies by means of your browser settings. Lack of adjustment of these settings means your consent for the Satel.pl website to use the cookies. See our Privacy Policy for more information.

Zamknij